pb rohs es52k1e05n-16.369m es52k1 e 05 n -16.369m series rohs compliant (pb-free) 3.0v 2.5mm x 3.2mm ceramic smd clipped sinewave tc(vc)xo operating temperature range -30c to +75c frequency stability 0.5ppm maximum nominal frequency 16.369mhz control voltage none (no connect on pad 1) electrical specifications nominal frequency 16.369mhz frequency stability vs. frequency tolerance 0.5ppm maximum (at 25c 2c, at vdd=3.0vdc, and vc=1.5vdc) frequency stability 0.5ppm maximum (inclusive of operating temperature range, at vdd=3.0vdc and vc=1.5vdc) frequency stability vs. input voltage 0.2ppm maximum (5%) frequency stability vs. aging 1ppm/year maximum (at 25c) frequency stability vs. load 0.2ppm maximum (1kohm//1pf) operating temperature range -30c to +75c supply voltage +3.0vdc 5% input current 2.0ma maximum output voltage 0.8vp-p clipped sinewave minimum (external dc-cut capacitor required, 1000pf recommended) load drive capability 10kohms//10pf output logic type clipped sinewave control voltage none (no connect on pad 1) phase noise -80dbc/hz at 10hz offset, -115dbc/hz at 100hz offset, -135dbc/hz at 1khz offset, and -148dbc/hz at 10khz offset (typical values at 16.368mhz) start up time 5msec maximum storage temperature range -55c to +125c environmental & mechanical specifications fine leak test mil-std-883, method 1014 condition a gross leak test mil-std-883, method 1014 condition c mechanical shock mil-std-202, method 213 condition c resistance to soldering heat mil-std-202, method 210 resistance to solvents mil-std-202, method 215 solderability mil-std-883, method 2003 temperature cycling mil-std-883, method 1010 vibration mil-std-883, method 2007 condition a www.ecliptek.com | specification subject to change without notice | rev a 3/13/2011 | page 1 of 4
es52k1e05n-16.369m mechanical dimensions (all dimensions in millimeters) pin connection 1 no connect 2 case/ground 3 output 4 supply voltage line marking 1 exx.xxx e=ecliptek xx.xxx=nominal frequency in mhz (5 digits maximum + decimal) 2 xxyzz xx=ecliptek manufacturing code y=last digit of the year zz=week of the year 1.6 0.9 0.9 (x4) 0.9 (x4) www.ecliptek.com | specification subject to change without notice | rev a 3/13/2011 | page 2 of 4 2.50 0.20 3.20 0.20 0.90 0.10 0.70 0.10 (x4) 1.60 0.10 1.10 0.10 0.80 0.10 (x4) marking orient a tion 1 2 3 4 all t oler ances are 0.1 sug g ested solder p ad la y out solder land (x4) all dimensions in millimeters output w a veform 0v dc clock output v p-p
t min s t max s critical zone t to t l p ramp-up ramp-down t l t p t 25 c to peak t preheat s t l t p temperature (t) time (t) recommended solder reflow methods es52k1e05n-16.369m high temperature infrared/convection ts max to tl (ramp-up rate) 3c/second maximum preheat - temperature minimum (ts min) 150c - temperature typical (ts typ) 175c - temperature maximum (ts max) 200c - time (ts min) 60 - 180 seconds ramp-up rate (tl to tp) 3c/second maximum time maintained above: - temperature (tl) 217c - time (tl) 60 - 150 seconds peak temperature (tp) 260c maximum for 10 seconds maximum target peak temperature (tp target) 250c +0/-5c time within 5c of actual peak (tp) 20 - 40 seconds ramp-down rate 6c/second maximum time 25c to peak temperature (t) 8 minutes maximum moisture sensitivity level level 1 www.ecliptek.com | specification subject to change without notice | rev a 3/13/2011 | page 3 of 4
t min s t max s critical zone t to t l p ramp-up ramp-down t l t p t 25 c to peak t preheat s t l t p temperature (t) time (t) recommended solder reflow methods es52k1e05n-16.369m low temperature infrared/convection 240c ts max to tl (ramp-up rate) 5c/second maximum preheat - temperature minimum (ts min) n/a - temperature typical (ts typ) 150c - temperature maximum (ts max) n/a - time (ts min) 60 - 120 seconds ramp-up rate (tl to tp) 5c/second maximum time maintained above: - temperature (tl) 150c - time (tl) 200 seconds maximum peak temperature (tp) 240c maximum target peak temperature (tp target) 240c maximum 1 time / 230c maximum 2 times time within 5c of actual peak (tp) 10 seconds maximum 2 times / 80 seconds maximum 1 time ramp-down rate 5c/second maximum time 25c to peak temperature (t) n/a moisture sensitivity level level 1 low temperature manual soldering 185c maximum for 10 seconds maximum, 2 times maximum. high temperature manual soldering 260c maximum for 5 seconds maximum, 2 times maximum. www.ecliptek.com | specification subject to change without notice | rev a 3/13/2011 | page 4 of 4
|
